Advanced Diploma in Electrical Design Engineering ✮

What you'll learn
Complete Electrical Design Engineering Training with Practical
Electrical equipment design for all projects like: oil & gas, chemical, power, pharmaceutical etc.
Detail engineering: Single line diagram, cable routing layout, earthing layout, lightening layout, lighting layout, substation layout, equipment layout
System Study: Load flow analysis, short circuit analysis, relay coordination, motor starting study, harmonic study
Equipment specification / datasheet for procurement.
3D Modeling, 2D Droughting, Analysis on software like: ETAP, DIALux, AutoCAD
Hazardous area classification
Lightning risk calculation, Report generation and layout
Coordination with other departments for input / output
Requirements
ETAP Software: for System Study / Simulation
DIALux software: for LUX calculation and layout
AutoCAD Software: for making the layout
Scientific Calculator: for sizing and calculation of electrical equipment
MS Excel: for making the datasheet / equipment specification for procurement purpose
Description
The goal is to design safe and dependable processing facilities in a cost effective manner. The fact is that there are very few formal training programs that focus on design and engineering of Electrical systems of such big plants The heavy electrical industry has under its purview power generation, transmission, distribution and utilization equipment. These include turbo generators, boilers, turbines, transformers, switchgears and other allied items. These electrical equipment (transformers, switchgears, etc.) are used by almost all the sectors. Some of the major areas where these are used include power generation projects, petrochemical, refineries, chemical plants, integrated steel plants, non-ferrous metal units, etc.
Overview:-
Introduction of Electrical Engineering
Introduction of EPC Industry
Coordination with Other Department
Load List:-
Preparation of Load Schedule
Determination of Power Supply Capacity
Standby Capacity consideration
Rating of Generators in Relation to
Prime Movers Importance of max and min temp
Rating of Motors in Relation to their Driven Machines
Electrical Equipment Selection, Sizing:-
Motor
Transformer
Emergency Generator
Neutral Grounding Resistor (NGR)
Power capacitor banks (PCB)
AC UPS
LV / HV / MV Switchgears
 Battery & Battery Charger
DC UPS
CT/PT
Power reactor
Bus duct
Illumination Design:-
Introduction
Type of Lighting Fixtures
Selection of Lighting Fixtures
Preparation of Fixtures Schedule
Indoor Illumination Calculation
Outdoor Illumination Calculation
Calculation on Software
Lighting Layout Design
Lighting Installation Detail
Small Power selection
Lighting Board Schedule
Cable Selection, Sizing & Layout:-
Power and Control cable Introduction
Cable Selection and Sizing
Cable sizing for Low voltage system
Cable sizing for High voltage system
Voltage Drop Consideration
Let through Energy consideration
Earth fault Loop Impedance consideration
Cable Schedule
Cable interconnection Schedule
Selection and Sizing of cable Tray
Cable tray schedule
Cable Drum schedule
Conduit Selection
Conduit Sizing
Cable Routing Layout
Cable Tagging
Installation details
Development of Single Line Diagram (SLD):-
Key SLD
Detail SLD
Lighting system SLD
Small power SLD
Metering and Control diagram
Hazardous Area Classification:-
Zone/Division Classification
Types of Protection for Hazardous Areas
Hazardous source List Preparation
Certification of Hazardous Area Equipment
Marking of Equipment Nameplates
Hazardous Area Drawings / Layouts Preparation
Earthing & Lightening Protection Design:-
Requirement of Earthing in Industrial Plants
Earthing Design calculations
Type of Earthing and Details
Earthing Installation Details
Earthing Layout Design
Lightening Protection Requirement
Lightening Protection Calculation
Lightening Installation Details
Lightening Layout Design
Substation / Switchyard Design:-
Introduction
Type of Sub-Stations
General arrangement of substation
Equipment Layout
Testing / System Studies:-
Overview & Load Flow Analysis
Short Circuit Analysis (Fault
Calculations and Stability Studies)
Motor Starting Study
Relay- Coordination
Procurements (Equipment Specification):-
Motor
Transformer
Emergency Generator
Power capacitor banks (PCB)
Cable
Who this course is for
ITI / Diploma / Degree / Master in Electrical or Electronics
Fresher / Experienced
People from other engineering background can also do the course if they have good math and electrical base experience.
Homepage

https://www.udemy.com/course/advanced-diploma-in-electrical-design-engineering/