Advanced Diploma in Electrical Design Engineering

What you'll learn
Complete Electrical Design Engineering Training with Practical
Electrical equipment design for all projects like: oil & gas, chemical, power, pharmaceutical etc.
Detail engineering: Single line diagram, cable routing layout, earthing layout, lightening layout, lighting layout, substation layout, equipment layout
System Study: Load flow analysis, short circuit analysis, relay coordination, motor starting study, harmonic study
Equipment specification / datasheet for procurement.
3D Modeling, 2D Droughting, Analysis on software like: ETAP, DIALux, AutoCAD
Hazardous area classification
Lightning risk calculation, Report generation and layout
Coordination with other departments for input / output
Requirements
ETAP Software: for System Study / Simulation
DIALux software: for LUX calculation and layout
AutoCAD Software: for making the layout
Scientific Calculator: for sizing and calculation of electrical equipment
MS Excel: for making the datasheet / equipment specification for procurement purpose
Description
The goal is to design safe and dependable processing facilities in a cost effective manner. The fact is that there are very few formal training programs that focus on design and engineering of Electrical systems of such big plants The heavy electrical industry has under its purview power generation, transmission, distribution and utilization equipment. These include turbo generators, boilers, turbines, transformers, switchgears and other allied items. These electrical equipment (transformers, switchgears, etc.) are used by almost all the sectors. Some of the major areas where these are used include power generation projects, petrochemical, refineries, chemical plants, integrated steel plants, non-ferrous metal units, etc.

Overview:-

Introduction of Electrical Engineering

Introduction of EPC Industry

Coordination with Other Department

Load List:-

Preparation of Load Schedule

Determination of Power Supply Capacity

Standby Capacity consideration

Rating of Generators in Relation to

Prime Movers Importance of max and min temp

Rating of Motors in Relation to their Driven Machines

Electrical Equipment Selection, Sizing:-

Motor

Transformer

Emergency Generator

Neutral Grounding Resistor (NGR)

Power capacitor banks (PCB)

AC UPS

LV / HV / MV Switchgears

 Battery & Battery Charger

DC UPS

CT/PT

Power reactor

Bus duct

Illumination Design:-

Introduction

Type of Lighting Fixtures

Selection of Lighting Fixtures

Preparation of Fixtures Schedule

Indoor Illumination Calculation

Outdoor Illumination Calculation

Calculation on Software

Lighting Layout Design

Lighting Installation Detail

Small Power selection

Lighting Board Schedule

Cable Selection, Sizing & Layout:-

Power and Control cable Introduction

Cable Selection and Sizing

Cable sizing for Low voltage system

Cable sizing for High voltage system

Voltage Drop Consideration

Let through Energy consideration

Earth fault Loop Impedance consideration

Cable Schedule

Cable interconnection Schedule

Selection and Sizing of cable Tray

Cable tray schedule

Cable Drum schedule

Conduit Selection

Conduit Sizing

Cable Routing Layout

Cable Tagging

Installation details

Development of Single Line Diagram (SLD):-

Key SLD

Detail SLD

Lighting system SLD

Small power SLD

Metering and Control diagram

Hazardous Area Classification:-

Zone/Division Classification

Types of Protection for Hazardous Areas

Hazardous source List Preparation

Certification of Hazardous Area Equipment

Marking of Equipment Nameplates

Hazardous Area Drawings / Layouts Preparation

Earthing & Lightening Protection Design:-

Requirement of Earthing in Industrial Plants

Earthing Design calculations

Type of Earthing and Details

Earthing Installation Details

Earthing Layout Design

Lightening Protection Requirement

Lightening Protection Calculation

Lightening Installation Details

Lightening Layout Design

Substation / Switchyard Design:-

Introduction

Type of Sub-Stations

General arrangement of substation

Equipment Layout

Testing / System Studies:-

Overview & Load Flow Analysis

Short Circuit Analysis (Fault

Calculations and Stability Studies)

Motor Starting Study

Relay- Coordination

Procurements (Equipment Specification):-

Motor

Transformer

Emergency Generator

Power capacitor banks (PCB)

Cable

Who this course is for
ITI / Diploma / Degree / Master in Electrical or Electronics
Fresher / Experienced
People from other engineering background can also do the course if they have good math and electrical base experience.